Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 270 | Manualshive

Page: 270 / 440

background image

WARNING!

•

Driving through standing water limits your vehi-
cle’s traction capabilities. Do not exceed 5 mph
(8 km/h) when driving through standing water.

•

Driving through standing water limits your vehi-
cle’s braking capabilities, which increases stop-
ping distances. Therefore, after driving through
standing water, drive slowly and lightly press on
the brake pedal several times to dry the brakes.

•

Getting water inside your vehicle’s engine can
cause it to lock up and stall out, and leave you
stranded.

•

Failure to follow these warnings may result in
injuries that are serious or fatal to you, your
passengers, and others around you.

POWER STEERING

The standard power steering system will give you good
vehicle response and increased ease of maneuverability
in tight spaces. The system will provide mechanical
steering capability if power assist is lost.

If for some reason the power assist is interrupted, it will
still be possible to steer your vehicle. Under these condi-
tions, you will observe a substantial increase in steering
effort, especially at very low vehicle speeds and during
parking maneuvers.

NOTE:

Increased noise levels at the end of the steering

wheel travel are considered normal and do not indicate
that there is a problem with the power steering system.

Upon initial start-up in cold weather, the power steering
pump may make noise for a short amount of time. This is
due to the cold, thick fluid in the steering system. This
noise should be considered normal, and it does not in any
way damage the steering system.

268

STARTING AND OPERATING

«
...
268
269
270
271
272
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: ABL Pages: 176

Brand: ABL Pages: 94

Brand: Federal Signal Corporation Pages: 8

Brand: Federal Signal Corporation Pages: 8

Brand: Mercedes-Benz Pages: 30

Chevrolet Silverado 2500HD 2021

Brand: GMC Pages: 433

Brand: Gator Pages: 2

Brand: GMC Pages: 120

Brand: Prime Tech Pages: 6

Brand: M7 SPEED Pages: 6

Brand: Fab Fours Pages: 13

Brand: Menabo Pages: 8

Brand: Mercedes-Benz Pages: 27

Brand: Quadratec Pages: 2

Brand: Lexus Pages: 609

Brand: Mitsubishi Pages: 284

Brand: HawksHead Pages: 10

Brand: Saab Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands