manualshive.com logo in svg

Dodge 2009 Challenger SRT8, Owner'S Manual

The 2009 Dodge Challenger SRT8 is a powerful and iconic muscle car, built for speed and style. To fully maximize your driving experience, it's crucial to have the corresponding Owner's Manual. Download the manual for free from our website, providing insightful instructions and essential information for your vehicle.

Share
Download
background image

This may result in a slightly different feeling or response
during normal operation in DRIVE position. After the
transmission cools down, it will return to normal
operation.

Brake/Transmission Shift Interlock System

This vehicle is equipped with a Brake Transmission Shift
Interlock (BTSI) system that holds the shift lever in the
PARK position when the ignition switch is in the LOCK
position. To move the shift lever out of the PARK
position, the ignition switch must be turned to the ON
position, and the brake pedal must be pressed.

Brake/Transmission Interlock Manual Override

There is an override for the BTSI that allows you to move
the shift lever out of the PARK position if an electrical
system malfunction occurs (i.e., dead battery). To access
the override (using a flat-bladed screwdriver), carefully
remove the override cover which is located on the right
of the shift lever.

Interlock Manual Override

258

STARTING AND OPERATING

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Metra Electronics 95-6556 Installation Instructions preview
95-6556
Brand: Metra Electronics Pages: 4
Rostra REARSIGHT OnStar 250-8822 Installation Instructions preview
REARSIGHT OnStar 250-8822
Brand: Rostra Pages: 2
AC Schnitzer X3 M-Technik Fitting Instructions Manual preview
X3 M-Technik
Brand: AC Schnitzer Pages: 20
Wagan Road Ready Seat Protector User Manual preview
Road Ready Seat Protector
Brand: Wagan Pages: 12
Chevrolet 2016 Suburban Owner'S Manual preview
2016 Suburban
Brand: Chevrolet Pages: 50
Safe Fleet PRIME DESIGN VRR-E-PM21 Assembly Instructions Manual preview
PRIME DESIGN VRR-E-PM21
Brand: Safe Fleet Pages: 12
AEM 30-3500 Instruction Manual preview
30-3500
Brand: AEM Pages: 27
CrimeStopper CA-504.BRKT Install Manual preview
CA-504.BRKT
Brand: CrimeStopper Pages: 1
Audiovox AA-BAT Programming Manual preview
AA-BAT
Brand: Audiovox Pages: 3
Victory 4x4 VRKCAP Install Instructions Manual preview
VRKCAP
Brand: Victory 4x4 Pages: 9
Rugged Ridge 11252.51 Installation Instructions preview
11252.51
Brand: Rugged Ridge Pages: 3
National Cycle Quantum Wash'n'Wipe N30208 Assembly Instructions And Owner'S Manual preview
Quantum Wash'n'Wipe N30208
Brand: National Cycle Pages: 12
Edelbrock 2917 Nstallation Instructions preview
2917 Nstallation
Brand: Edelbrock Pages: 1
Saab 2000 9-5 2.3 Turbo Ecopower Owner'S Manual preview
2000 9-5 2.3 Turbo Ecopower
Brand: Saab Pages: 256
Thule 1597 Instructions preview
1597
Brand: Thule Pages: 4
Mobileye C2-270 User Manual preview
C2-270
Brand: Mobileye Pages: 29
EUFAB 11512 Manual preview
11512
Brand: EUFAB Pages: 4
Soundoff Signal nERGY ETSA200R-PA Quick Start Manual preview
nERGY ETSA200R-PA
Brand: Soundoff Signal Pages: 3

Brands by name

Popular brands

Load more brands