manualshive.com logo in svg

Dodge 2009 Challenger SRT8, Owner'S Manual

The 2009 Dodge Challenger SRT8 is a powerful and iconic muscle car, built for speed and style. To fully maximize your driving experience, it's crucial to have the corresponding Owner's Manual. Download the manual for free from our website, providing insightful instructions and essential information for your vehicle.

Share
Download
background image

Loose Fuel Filler Cap Message

If the vehicle diagnostic system determines that the fuel
filler cap is loose, improperly installed, or damaged, a
“Check Gascap” message will display in the Electronic
Vehicle Information Center (EVIC). If this occurs, tighten
the fuel filler cap properly and press the TRIP ODOM-
ETER button to turn off the message. If the problem
continues, the message will appear the next time the
vehicle is started.

A loose, improperly installed, or damaged fuel filler cap
may also turn on the MIL. Refer to “Onboard Diagnostic
System” in Section 7.

VEHICLE LOADING

The load carrying capacity of your vehicle is shown on the
“Vehicle Certification Label.” This information should be
used for passenger and luggage loading as indicated.

Do not exceed the specified Gross Vehicle Weight Rating
(GVWR) or the Gross Axle Weight Rating (GAWR).

Vehicle Certification Label

Your vehicle has a Vehicle Certification Label affixed to
the rear of the driver’s door.

The label contains the following information:

•

Name of manufacturer

•

Month and year of manufacture

•

Gross Vehicle Weight Rating (GVWR)

•

Gross Axle Weight Rating (GAWR) front

•

Gross Axle Weight Rating (GAWR) rear

•

Vehicle Identification Number (VIN)

•

Type of Vehicle

•

Month Day and Hour of Manufacture (MDH)

The bar code allows a computer scanner to read the VIN.

STARTING AND OPERATING

315

5

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

GARO ENTITY PRO Installation preview
ENTITY PRO
Brand: GARO Pages: 2
John Gold Gold Cruuse Cruisecontrol GC90 Installation Manual preview
Gold Cruuse Cruisecontrol GC90
Brand: John Gold Pages: 24
Whispbar K498W Fitting Instructions Manual preview
K498W
Brand: Whispbar Pages: 14
Draw tite 24943 Installation Instructions preview
24943
Brand: Draw tite Pages: 4
Mercedes-Benz CLS 280 2008 Owner'S Manual preview
CLS 280 2008
Brand: Mercedes-Benz Pages: 329
M7 SPEED AGS-R2 Manual preview
AGS-R2
Brand: M7 SPEED Pages: 6
Park-Daddy PD50AA Installation Manual preview
PD50AA
Brand: Park-Daddy Pages: 22
Joie i-Level Instruction Manual preview
i-Level
Brand: Joie Pages: 53
Saturn 2007 Ion Owner'S Manual preview
2007 Ion
Brand: Saturn Pages: 440
Whelen Engineering Company LED Dominator TAM83S2 Installation Manual preview
LED Dominator TAM83S2
Brand: Whelen Engineering Company Pages: 2
Metra Electronics 99-7804 Installation Instructions Manual preview
99-7804
Brand: Metra Electronics Pages: 10
Kleinn Air Horns RNGR-102-1/220 Installation Manual preview
RNGR-102-1/220
Brand: Kleinn Air Horns Pages: 33
Volvo 2009 S40 Owner'S Manual preview
2009 S40
Brand: Volvo Pages: 286
Opel MERIVA 2014 Brochure & Specs preview
MERIVA 2014
Brand: Opel Pages: 44
Setma E12AU02002 Instruction Manual preview
E12AU02002
Brand: Setma Pages: 16
Yakima RIpCord Manual preview
RIpCord
Brand: Yakima Pages: 12
VER-MAC PCMS-1210 QS User Manual preview
PCMS-1210 QS
Brand: VER-MAC Pages: 44
Classic Accessories Quad Gear 18-029-010401-00-SC Instructions preview
Quad Gear 18-029-010401-00-SC
Brand: Classic Accessories Pages: 4

Brands by name

Popular brands

Load more brands