Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 251 | Manualshive

Page: 251 / 440

background image

If Engine Fails To Start

WARNING!

•

Never pour fuel or other flammable liquids into
the throttle body air inlet opening in an attempt to
start the vehicle. This could result in a flash fire
causing serious personal injury.

(Continued)

WARNING! (Continued)

•

Do not attempt to push or tow your vehicle to get
it started. Vehicles equipped with an automatic
transmission cannot be started this way. Unburned
fuel could enter the catalytic converter and once
the engine has started, ignite and damage the
converter and vehicle. If the vehicle has a dis-
charged battery, booster cables may be used to
obtain a start from a booster battery or the battery
in another vehicle. This type of start can be dan-
gerous if done improperly. Refer to Section 6 for
proper jump-starting procedures and follow them
carefully.

STARTING AND OPERATING

249

5

«
...
249
250
251
252
253
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Jackco Pages: 11

Brand: Metra Electronics Pages: 2

Brand: Prorack Pages: 14

Transit Vancouver Wagon

Brand: Webasto Pages: 44

Brand: Waeco Pages: 172

Brand: VBG Pages: 16

Brand: Fast Master Products Pages: 13

Brand: T-Mobile Pages: 2

Brand: Carcomm Pages: 2

Brand: Demco Pages: 4

Brand: Broadfeet Pages: 2

Brand: Lexus Pages: 6

Brand: Guardsman Pages: 2

Brand: Quadratec Pages: 2

Brand: MovaNext Pages: 4

Brand: TRAMEC Pages: 116

Brand: NavInc Pages: 5

Brand: Davis Instruments Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands