Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 363 | Manualshive

Page: 363 / 440

background image

CAUTION! (Continued)

•

The fluid level is preset at the factory and it does
not require adjustment under normal operating
conditions. If a transmission fluid leak occurs,
visit your authorized dealer immediately. Severe
damage to the transmission may occur. Your au-
thorized dealer has the proper tools to adjust the
fluid level accurately.

Fluid and Filter Changes

Refer to the “Maintenance Schedule” in Section 8 for the
proper maintenance intervals.

If the transmission is disassembled for any reason, the
fluid and filter should be changed.

Selection of Lubricant

It is important that the proper lubricant is used in the
transmission to assure optimum transmission perfor-
mance. Use only manufacturer’s recommended transmis-
sion fluid. Refer to “Fluids, Lubricants, and Genuine
Parts” in this section for the correct fluid type. It is
important that the transmission fluid be maintained at
the prescribed level using the recommended fluid. No
chemical flushes should be used in any transmission;
only the approved lubricant may be used.

Special Additives

Automatic Transmission Fluid (ATF) is an engineered
product and its performance may be impaired by supple-
mental additives. Therefore, do not add any fluid addi-
tives to the transmission. The only exception to this
policy is the use of special dyes to aid in detecting fluid
leaks. In addition, avoid using transmission sealers as
they may adversely affect seals.

MAINTAINING YOUR VEHICLE

361

7

«
...
361
362
363
364
365
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Kuda-Phonebase Pages: 3

Brand: Subaru Pages: 99

Brand: Sirius Satellite Radio Pages: 8

CB-796IG2-CIGD-R

Brand: CARRYBOY Pages: 4

Brand: GMC Pages: 428

Brand: Cadillac Pages: 518

Brand: Opel Pages: 141

Carpower CAP-20

Brand: Monacor Pages: 2

Brand: Mercedes-Benz Pages: 54

Brand: Jaeger Pages: 17

2014 Grand Cherokee SRT8

Brand: Jeep Pages: 596

Brand: Skoda Pages: 4

1506-PHX Cargo Plus

Brand: Ranger design Pages: 8

Brand: AUTOTECH Pages: 1

Brand: travall Pages: 4

Brand: TOPPOINT Pages: 2

Brand: Billien Pages: 2

Brand: Lexus Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands