Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 356 | Manualshive

Page: 356 / 440

background image

Cooling System — Drain, Flush, and Refill

If the solution is dirty or contains a considerable amount
of sediment, clean and flush with a reliable cooling
system cleaner. Follow with a thorough rinsing to remove
all deposits and chemicals. Properly dispose of the old
antifreeze solution.

Refer to the “Maintenance Schedule” in Section 8 for the
proper maintenance intervals.

Selection of Coolant

Use only the manufacturer’s recommended coolant. Re-
fer to “Fluids, Lubricants, and Genuine Parts” in this
section for the correct fluid type.

CAUTION!

•

Mixing of coolants other than specified HOAT
engine coolants may result in engine damage and
may decrease corrosion protection. If a non-HOAT
coolant is introduced into the cooling system in an
emergency, it should be replaced with the speci-
fied coolant as soon as possible.

•

Do not use plain water alone or alcohol-based
engine coolant (antifreeze) products. Do not use
additional rust inhibitors or antirust products, as
they may not be compatible with the radiator
engine coolant and may plug the radiator.

•

This vehicle has not been designed for use with
propylene glycol-based coolants. Use of propylene
glycol-based coolants is not recommended.

354

MAINTAINING YOUR VEHICLE

«
...
354
355
356
357
358
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Laser Pages: 8

10-8002-C11998B

Brand: Saleen Pages: 12

2013 Buick Verano

Brand: Buick Pages: 5

2005 Sierra Denali

Brand: GMC Pages: 428

Brand: Mercedes-Benz Pages: 346

Brand: Thule Pages: 4

Brand: Audi Pages: 9

Brand: Belkin Pages: 4

Brand: Audi Pages: 12

MAGNUM RT Series

Brand: Raptor Series Pages: 6

Brand: Cadillac Pages: 20

Brand: Fab Fours Pages: 21

Brand: Quadratec Pages: 12

Brand: MULTILIFT Pages: 62

Brand: Camoplast Pages: 19

Brand: Lincoln Pages: 586

Ridesmart KMA-610

Brand: KlipXtreme Pages: 12

Brand: TOP VEHICLE TECH Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands