Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 362 | Manualshive

Page: 362 / 440

background image

the proper level. Refer to “Fluids, Lubricants, and Genu-
ine Parts” in this section for the correct fluid type.

CAUTION!

Using a transmission fluid other than the manufac-
turer’s recommended fluid may cause deterioration
in transmission shift quality and/or damage to the
transmission. Refer to “Fluids, Lubricants, and
Genuine Parts” in this section for the correct fluid
type.

Change Transmission Fluid

If contaminated with water, change the fluid immedi-
ately. See your authorized dealer for service.

Refer to the “Maintenance Schedule” in Section 8 for the
proper maintenance intervals.

Automatic Transmission — If Equipped

Fluid Level Check

Regular automatic transmission fluid level checks are not
required. For this reason, the dipstick is omitted.

If you notice fluid loss or gear shift malfunction, have
your authorized dealer check the transmission fluid level.

CAUTION!

•

Using a transmission fluid other than the manu-
facturer’s recommended fluid may cause deterio-
ration in transmission shift quality and/or torque
converter shudder. Using a transmission fluid
other than that recommended by the manufacturer
will result in more frequent fluid and filter
changes. Refer to “Fluids, Lubricants, and Genu-
ine Parts” in this section for the correct fluid type.

(Continued)

360

MAINTAINING YOUR VEHICLE

«
...
360
361
362
363
364
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Camcar Pages: 2

Brand: J-Top Pages: 2

Brand: Jeep Pages: 603

Brand: Jeep Pages: 80

Brand: ECS Electronics Pages: 16

Brand: SCC Pages: 4

Brand: Aries Pages: 5

Brand: Mercedes-Benz Pages: 354

Brand: Saturn Pages: 440

Fleetwood Brougham Sedan 1966

Brand: Cadillac Pages: 56

Brand: Honda Pages: 24

Brand: Ford Pages: 585

Brand: Honda Pages: 4

Brand: Pet Gear Pages: 4

Brand: Mid America Motorworks Pages: 2

Brand: TrailFX Pages: 3

PRIME DESIGN HRR-NV11B

Brand: Safe Fleet Pages: 12

1996 Civic Del Sol

Brand: Honda Pages: 219

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands