Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 357 | Manualshive

Page: 357 / 440

background image

Adding Coolant

Your vehicle has been built with an improved engine
coolant that allows extended maintenance intervals. This
coolant can be used up to five years or 102,000 miles
(170 000 km) before replacement. To prevent reducing
this extended maintenance period, it is important that
you use the same coolant throughout the life of your
vehicle. Please review these recommendations for using
Hybrid Organic Additive Technology (HOAT) coolant.

When adding coolant:

•

The manufacturer recommends using MOPAR

威

Antifreeze/Coolant 5 Year/100,000 Mile Formula
HOAT (Hybrid Organic Additive Technology).

•

Mix a minimum solution of 50% HOAT engine coolant
and distilled water. Use higher concentrations (not to
exceed 70%) if temperatures below

⫺

34°F (

⫺

37°C) are

anticipated.

•

Use only high purity water such as distilled or deion-
ized water when mixing the water/engine coolant
solution. The use of lower quality water will reduce
the amount of corrosion protection in the engine
cooling system.

Please note that it is the owner’s responsibility to main-
tain the proper level of protection against freezing ac-
cording to the temperatures occurring in the area where
the vehicle is operated.

NOTE:

Mixing coolant types will decrease the life of the

engine coolant and will require more frequent coolant
changes.

Cooling System Pressure Cap

The cap must be fully tightened to prevent loss of coolant
and to ensure that coolant will return to the radiator from
the coolant recovery bottle.

MAINTAINING YOUR VEHICLE

355

7

«
...
355
356
357
358
359
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Jeep Pages: 42

Brand: Jeep Pages: 44

Brand: Cadillac Pages: 20

Brand: Jeep Pages: 7

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 354

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 10

2013 Escalade ESV

Brand: Cadillac Pages: 524

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 438

Brand: Cadillac Pages: 450

2011 Escalade Hybrid

Brand: Cadillac Pages: 94

2011 Escalade Hybrid

Brand: Cadillac Pages: 94

Brand: Cadillac Pages: 78

Brand: Cadillac Pages: 8

Brand: Cadillac Pages: 113

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands