Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 41 | Manualshive

Page: 41 / 440

background image

WARNING! (Continued)

•

A shoulder belt placed behind you will not protect

you from injury during a collision. You are more
likely to hit your head in a collision if you do not
wear your shoulder belt. The lap and shoulder belt
are meant to be used together.

4. Position the lap belt across your thighs, below your
abdomen. To remove slack in the lap belt portion, pull up
a bit on the shoulder belt. To loosen the lap belt if it is too
tight, tilt the latch plate and pull on the lap belt. A snug
belt reduces the risk of sliding under the belt in a
collision.

WARNING!

•

A lap belt worn too high can increase the risk of

internal injury in a collision. The belt forces won’t be
at the strong hip and pelvic bones, but across your
abdomen. Always wear the lap belt as low as pos-
sible and keep it snug.

•

A twisted belt cannot do its job as well. In a

collision, it could even cut into you. Be sure the belt
is straight. If you cannot straighten a belt in your
vehicle, take it to your authorized dealer and have it
fixed.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

39

2

«
...
39
40
41
42
43
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Thule Pages: 8

Brand: Cadillac Pages: 407

Brand: Subaru Pages: 16

JEEP GL ADIATOR JT TOPPER ROOF RACK

Brand: JCROffroad Pages: 7

IVH-9000-2R440Q

Brand: Vecow Pages: 110

Brand: ConWys AG Pages: 16

Easy Air Auto Screen

Brand: Wagan Pages: 8

Prime Design VBI-FT31B

Brand: Safe Fleet Pages: 12

Prime Design OCM-3032

Brand: Safe Fleet Pages: 4

Brand: Toyota Pages: 285

Brand: Honda Pages: 4

Brand: Pet Gear Pages: 4

Brand: Husky Pages: 8

Brand: Kia Pages: 5

Brand: Curt Group Pages: 2

Brand: Saab Pages: 16

Brand: Whispbar Pages: 34

Brand: U.S. General Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands