Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 281 | Manualshive

Page: 281 / 440

background image

WARNING!

There may be situations on minor hills (i.e., less than
8%), with a loaded vehicle, or while pulling a trailer,
when the system will not activate and slight rolling
may occur. This could cause a collision with another
vehicle or object. Always remember the driver is
responsible for braking the vehicle.

Disabling/Enabling HSA

If you wish to turn on or off the HSA system, it can be
done using the Customer Programmable Features in the
Electronic Vehicle Information Center (EVIC). Refer to
“Electronic Vehicle Information Center (EVIC)” in Sec-
tion 4 of this manual.

For vehicles not equipped with the EVIC, perform the
following steps:

NOTE:

You must complete Steps 1 through 8 within

90 seconds.

1. Center the steering wheel (front wheels pointing
straight forward).

2. Shift the transmission into NEUTRAL.

3. Apply the parking brake.

4. Start the engine.

5. Release the clutch pedal.

6. Rotate the steering wheel one-half turn to the left.

7. Press the ESP OFF switch (located in the lower switch
bank below the climate controls) four times within 20 sec-
onds. The “ESP/TCS Indicator Light” should turn on and
turn off two times.

STARTING AND OPERATING

279

5

«
...
279
280
281
282
283
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Wallbox Pages: 7

Wallbox eM4 Single

Brand: ABL Pages: 68

Brand: Alpine Pages: 8

Brand: Hyundai Pages: 280

Brand: Nuna Pages: 17

inView 360 Fusion

Brand: Safe Fleet Pages: 27

ROADSIDE ASSISTANCE

Brand: Seat Pages: 44

Brand: FALCON RIDGE Pages: 7

Brand: Volvo Pages: 30

Brand: Mitsubishi Pages: 19

Brand: Paser Pages: 2

Brand: Xblitz Pages: 56

Grand Cherokee SRT 2019

Brand: Jeep Pages: 656

Brand: SSV Works Pages: 2

Brand: iSimple Pages: 12

Brand: Yakima Pages: 10

Brand: Kuda Pages: 4

Brand: Sanixair Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands