Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 16 | Manualshive

Page: 16 / 440

background image

NOTE:

The power window switches, radio, power

sunroof (if equipped), and ignition-powered power out-
lets will remain active for up to 60 minutes after the
ignition switch is turned to the LOCK position. Opening
either door will cancel this feature. The time for this
feature is programmable. Refer to “Delay Power Off to
Accessories Until Exit,” under “Personal Settings (Cus-
tomer Programmable Features),” under “Electronic Ve-
hicle Information Center (EVIC)” in Section 4.

WARNING!

Never leave children alone in a vehicle. Leaving
unattended children in a vehicle is dangerous for a
number of reasons. A child or others could be seri-
ously or fatally injured. Don’t leave the key in the
ignition. A child could operate power windows,
other controls, or move the vehicle.

CAUTION!

An unlocked car is an invitation to thieves. Always
remove key from the ignition and lock all doors
when leaving the vehicle unattended.

Key-In-Ignition Reminder

If you open the driver’s door and the key is in the
ignition, a chime will sound to remind you to remove the
key.

NOTE:

The Key-In-Ignition reminder only sounds

when the ignition key is placed in the LOCK or ACC
position.

SENTRY KEY

姞

The Sentry Key

威

Immobilizer System prevents unautho-

rized vehicle operation by disabling the engine. The
system does not need to be armed or activated. Operation

14

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
14
15
16
17
18
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Ranger design Pages: 6

Brand: GARO Pages: 23

LS4 Wallmounted

Brand: GARO Pages: 15

Brand: Yakima Pages: 6

Brand: Yakima Pages: 18

Retrotech RTX-68D-CHG

Brand: Dakota Digital Pages: 4

Brand: Ironton Pages: 7

Intercooler Kit Type 31

Brand: GReddy Pages: 9

Brand: U.S. General Pages: 8

Brand: E&G Classics Pages: 3

Brand: A-Tach Mounts Pages: 2

Brand: Bilstein Pages: 7

Brand: Prime Design Pages: 8

Brand: Westin Pages: 3

EPS-LD SafePark

Brand: Tobe Pages: 2

Brand: Scion Pages: 58

Brand: RAM Pages: 288

Forester 2.5X 2003

Brand: Subaru Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands