Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 50 | Manualshive

Page: 50 / 440

background image

seat as far back as possible and use the proper child
restraint. (Refer to information on Child Restraint in this
section.)

5. You should read the instructions provided with your
child restraint to make sure that you are using it properly.

6. All occupants should use their seat belts properly.

7. The driver and front passenger seats should be moved
back as far as practical to allow the airbags time to inflate.

8. Do not lean against the door, as the airbags will inflate
forcefully into the space between you and the door.

9. If the airbag system in this vehicle needs to be
modified to accommodate a disabled person, contact the
Customer Center. Phone numbers are provided in the

⬙

If

You Need Customer Assistance

⬙

section.

WARNING!

•

Relying on the airbags alone could lead to more
severe injuries in a collision. The airbags work
with your seat belt to restrain you properly. In
some collisions, the airbags won’t deploy at all.
Always wear your seat belts even though you have
airbags.

•

Being too close to the steering wheel or instrument
panel during airbag deployment could cause seri-
ous injury. Airbags need room to inflate. Sit back,
comfortably extending your arms to reach the
steering wheel or instrument panel.

•

This vehicle has supplemental side curtain air-
bags, and they need room to inflate. Do not lean
against the door or window. Sit upright in the
center of the seat.

48

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
48
49
50
51
52
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: FABBRI PORTATUTTO Pages: 2

Brand: Ford Pages: 12

Brand: Ford Pages: 2

Brand: DAVIS Pages: 32

2005 Sierra Denali

Brand: GMC Pages: 428

Brand: Mercedes-Benz Pages: 346

Brand: Thule Pages: 4

Brand: GMC Pages: 425

Brand: WABCO Pages: 32

PRIME DESIGN VRR-E-PM21

Brand: Safe Fleet Pages: 12

v.LOGiC Intelligent Solution V5-NTG46

Brand: Caraudio-Systems Pages: 18

Brand: TBC Pages: 12

Brand: Prorack Pages: 14

Magic Watch MWE-850-4DSM

Brand: Waeco Pages: 204

Interlock 700 Series

Brand: Scania Pages: 82

Brand: Mercedes-Benz Pages: 398

Prestige 128-8602

Brand: Audiovox Pages: 8

Brand: Car-Interface Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands