Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 398

Page: 398 / 440

96,000 Miles (160,000 km) or 96 Months Maintenance Service
Schedule

❏

Change the engine oil and engine oil filter.

❏

Rotate tires.

❏

If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner
filter, and replace if necessary.

❏

Replace the air conditioning filter.

❏

Inspect the brake linings, and replace if necessary.

❏

Inspect the CV joints.

❏

Inspect the exhaust system.

❏

Inspect the front suspension, tie rod ends and boot seals, and replace if necessary.

❏

Change the rear axle fluid if using your vehicle for any of the following: police, taxi, fleet,
or frequent trailer towing.

❏

Change the manual transmission fluid (if equipped).

Odometer Reading

Date

Repair Order #

Dealer Code

Signature Authorized Chrysler Dealer

102,000 Miles (170,000 km) or
102 Months Maintenance
Service Schedule

❏

Change the engine oil and engine oil
filter.

❏

Rotate tires.

❏

Replace the spark plugs.

❏

Flush and replace the engine coolant if
not done at 60 months.

Odometer Reading

Date

Repair Order #

Dealer Code

Signature Authorized Chrysler Dealer

396

MAINTENANCE SCHEDULES

T
E

N
A
N
C

S
C
H
E
D
U
L
E
S

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Search results

Summary of Contents for 2009 Challenger SRT8

Reviews:

Related manuals for 2009 Challenger SRT8

Brands by name

Popular brands

Dodge 2009 Challenger SRT8, Owner'S Manual

Search results

Summary of Contents for 2009 Challenger SRT8

Reviews:

Related manuals for 2009 Challenger SRT8

Brands by name

Popular brands