Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 287 | Manualshive

Page: 287 / 440

background image

NOTE:

•

The “ESP/TCS Indicator Light” and the “ESP/BAS
Malfunction Indicator Light” will turn on momen-
tarily each time the ignition switch is turned ON.

•

Each time the ignition is turned ON, the ESP System
will be ON even if it was turned OFF previously.

•

The ESP Control System will make buzzing or clicking
sounds when it is active. This is normal; the sounds
will stop when the ESP becomes inactive following the
maneuver that caused the ESP activation.

TIRE SAFETY INFORMATION

Tire Markings

1 — U.S. DOT Safety Stan-

dards Code (TIN)

4 — Maximum Load

2 — Size Designation

5 — Maximum Pressure

3 — Service Description

6 — Treadwear, Traction and

Temperature Grades

STARTING AND OPERATING

285

5

«
...
285
286
287
288
289
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: B-Speech Pages: 18

Brand: Whispbar Pages: 16

Brand: Ford Pages: 22

Autostacker PL-6SR

Brand: BendPak Pages: 104

PACCAR PACMOBILE 20

Brand: DAF Pages: 18

Brand: TATA Motors Pages: 236

Brand: Paser Pages: 2

Brand: Xblitz Pages: 56

Brand: Rugged Ridge Pages: 2

MultiCharger 1204

Brand: DEFA Pages: 28

Brand: Steelmate Pages: 14

Brand: GReddy Pages: 12

INDICA eV2 XETA CNG

Brand: TATA Motors Pages: 24

Brand: PAC Pages: 5

Brand: Percon Pages: 49

Brand: Jeep Pages: 374

Escalade 2004 Escalade ESV

Brand: Cadillac Pages: 472

Brand: Scosche Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands