Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 68 | Manualshive

Page: 68 / 440

background image

CAUTION!

Never use Non-Detergent Oil or Straight Mineral Oil
in the engine or damage may result.

NOTE:

A new engine may consume some oil during its

first few thousand miles (kilometers) of operation. This
should be considered a normal part of the break-in and
not interpreted as an indication of difficulty.

SAFETY TIPS

Transporting Passengers

NEVER TRANSPORT PASSENGERS IN THE CARGO
AREA.

WARNING!

•

It is extremely dangerous to ride in a cargo area,
inside or outside of a vehicle. In a collision, people
riding in these areas are more likely to be seri-
ously injured or killed.

•

Do not allow people to ride in any area of your
vehicle that is not equipped with seats and seat
belts.

•

Be sure everyone in your vehicle is in a seat and
using a seat belt properly.

66

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
66
67
68
69
70
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Toyota Pages: 529

Brand: Hama Pages: 6

Brand: GARO Pages: 2

Brand: FORM FIT Pages: 2

Brand: TATA Motors Pages: 156

Brand: Volvo Pages: 188

MagicComfort MSH200

Brand: Waeco Pages: 108

Brand: Tusk Pages: 2

Brand: TATA Motors Pages: 92

Brand: Fab Fours Pages: 21

DAF CHARGEMAX 90

Brand: Paccar Pages: 40

Brand: v.LOGiC Pages: 22

Brand: Mercedes-Benz Pages: 91

Interlock 700 Series

Brand: Scania Pages: 82

Brand: Mercedes-Benz Pages: 493

Brand: Volvo Pages: 286

Brand: Yakima Pages: 10

Brand: Ford Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands