manualshive.com logo in svg

Dodge 2009 Challenger SRT8, Owner'S Manual

The 2009 Dodge Challenger SRT8 is a powerful and iconic muscle car, built for speed and style. To fully maximize your driving experience, it's crucial to have the corresponding Owner's Manual. Download the manual for free from our website, providing insightful instructions and essential information for your vehicle.

Share
Download
background image

3. Set the parking brake, place the automatic transmis-
sion in PARK (manual transmission in NEUTRAL), and
turn the ignition switch to the LOCK position on both
vehicles.

4. Turn off the heater, radio, and all unnecessary electri-
cal loads.

5. Connect one end of the jumper cable to the remote
jump-start positive battery post

(+)

in the engine com-

partment. Connect the other end of the same cable to the
positive terminal of the booster battery. Refer to the
following illustration for jump-starting connections.

6. Connect the other cable, first to the negative terminal
of the booster battery and

then to the engine ground (-)

of the vehicle with the discharged battery.

Make sure

you have a good contact on the engine ground. Refer to
the following illustration for jump-starting connections.

7. Start the engine in the vehicle that has the booster
battery. Let the engine idle a few minutes. Then, start the
engine in the vehicle with the discharged battery.

NOTE:

Refer to

⬙

Synchronizing ESP

⬙

under

⬙

Electronic

Stability Program

⬙

in Section 5 if the ESP/BAS light (in

Jump-Starting

WHAT TO DO IN EMERGENCIES

329

6

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

TATA Motors Safari Owner'S Manual & Service Book preview
Safari
Brand: TATA Motors Pages: 161
TAUBENREUTHER 16 - 590 Fitting Instructions Manual preview
16 - 590
Brand: TAUBENREUTHER Pages: 11
Yakima SKYBOX Series Manual preview
SKYBOX Series
Brand: Yakima Pages: 15
Barker 25895 Owner'S Instructions preview
25895
Brand: Barker Pages: 2
MAcarbon Ferrari 360 Map Carbon Light Installation Instructions preview
Ferrari 360 Map Carbon Light
Brand: MAcarbon Pages: 4
Kia CADENZA 2017 Features & Functions Manual preview
CADENZA 2017
Brand: Kia Pages: 58
Columbia THERAPEDIC 2000 Instructions For Use Manual preview
THERAPEDIC 2000
Brand: Columbia Pages: 14
Honda 2009 S2000 Owner'S Manual preview
2009 S2000
Brand: Honda Pages: 268
Acura RLX 2016 Service Bulletin preview
RLX 2016
Brand: Acura Pages: 7
Lexus LS 460 2011 Owner'S Manual preview
LS 460 2011
Brand: Lexus Pages: 830
Honda Civic Hatch 2017 Owner'S Manual preview
Civic Hatch 2017
Brand: Honda Pages: 687
AUTOTECH 10.109.418K Installation Instructions preview
10.109.418K
Brand: AUTOTECH Pages: 4
Kleinn Air Horns RNGR-102-1/220 Installation Manual preview
RNGR-102-1/220
Brand: Kleinn Air Horns Pages: 33
travall TDG1166 Fitting Instructions preview
TDG1166
Brand: travall Pages: 4
A-Tach Mounts 50321 Quick Start Manual preview
50321
Brand: A-Tach Mounts Pages: 2
Thule 2087 Parts List preview
2087
Brand: Thule Pages: 1
Tuff Tonneaus Bunji Ute Installation Instructions preview
Bunji Ute
Brand: Tuff Tonneaus Pages: 4
AA Products RB0002 Instruction Manual preview
RB0002
Brand: AA Products Pages: 6

Brands by name

Popular brands

Load more brands