Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 125 | Manualshive

Page: 125 / 440

background image

Multifunction Lever

The multifunction lever controls the operation of the turn
signals, headlight beam selection, and passing lights. The
multifunction lever is located on the left side of the
steering column.

Turn Signals

Move the multifunction lever up or down and the
corresponding turn signal indicator in the instrument
cluster flashes to show proper operation of the front and
rear turn signal lights.

If either indicator has a very fast flash rate, check for a
defective outside light bulb. If an indicator fails to light
when the multifunction lever is moved, see your autho-
rized dealer for service.

NOTE:

A “Turn Signal On” message will appear in the

Electronic Vehicle Information Center (EVIC) and a con-
tinuous chime will sound if the vehicle is driven more
than 1 mile (1.6 km) with either turn signal on.

Lane Change Assist

Tap the lever up or down once and the turn signal (left or
right) will flash three times then automatically turn off.

Multifunction Lever

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

123

3

«
...
123
124
125
126
127
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

ESCALADE - BROCHURE 2009

Brand: Cadillac Pages: 24

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 20

Green Motion DC 22

Brand: Eaton Pages: 65

CK 3000 Evolution

Brand: Parrot Pages: 2

Brand: Yakima Pages: 7

Brand: Yakima Pages: 6

Brand: Yakima Pages: 10

Brand: Yakima Pages: 12

Brand: Kia Pages: 385

Prestige APS-45B

Brand: Audiovox Pages: 8

Brand: Volvo Pages: 138

5TH GEN 4RUNNER

Brand: Victory 4x4 Pages: 5

Brand: Keith Pages: 2

Brand: SnapPad Pages: 5

Brand: Yakima Pages: 11

Brand: Vauxhall Pages: 259

Brand: Beper Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands