manualshive.com logo in svg

Dodge 2009 Challenger SRT8, Owner'S Manual

The 2009 Dodge Challenger SRT8 is a powerful and iconic muscle car, built for speed and style. To fully maximize your driving experience, it's crucial to have the corresponding Owner's Manual. Download the manual for free from our website, providing insightful instructions and essential information for your vehicle.

Share
Download
background image

Rear Axle

Fluid Level Check

Check the fluid level by removing the fill plug on the
axle. The fluid level should be at the bottom of the fill
hole. Add fluid, if necessary, to maintain the proper level.
Refer to “Fluids, Lubricants, and Genuine Parts” in this
section for the correct fluid type.

Change Axle Fluid

Refer to the “Maintenance Schedule” in Section 8 for the
proper maintenance intervals.

Appearance Care and Protection from Corrosion

Protection of Body and Paint from Corrosion

Vehicle body care requirements vary according to geo-
graphic locations and usage. Chemicals that make roads
passable in snow and ice, and chemicals that are sprayed
on trees and road surfaces during other seasons, are
highly corrosive to the metal in your vehicle. Outside

parking, which exposes your vehicle to airborne contami-
nants, road surfaces on which the vehicle is operated,
extreme hot or cold weather and other extreme condi-
tions will have an adverse effect on paint, metal trim, and
underbody protection.

The following maintenance recommendations will enable
you to obtain maximum benefit from the corrosion
resistance built into your vehicle.

What Causes Corrosion?

Corrosion is the result of deterioration or removal of
paint and protective coatings from your vehicle.
The most common causes are:

•

Road salt, dirt, and moisture accumulation.

•

Stone and gravel impact.

•

Insects, tree sap, and tar.

•

Salt in the air near seacoast localities.

•

Atmospheric fallout/industrial pollutants.

362

MAINTAINING YOUR VEHICLE

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Panasonic SL-SX451C Operating Instructions preview
SL-SX451C
Brand: Panasonic Pages: 2
Panasonic CYRC50U - UNIVERSAL REAR-VIEW CAMERA Manual De Instrucciones preview
CYRC50U - UNIVERSAL REAR-VIEW CAMERA
Brand: Panasonic Pages: 20
Panasonic CF-WEB Series Setting Manual preview
CF-WEB Series
Brand: Panasonic Pages: 12
Jeep Wrangler2018 Owner'S Manual preview
Wrangler2018
Brand: Jeep Pages: 608
Yakima K1188 Instructions Manual preview
K1188
Brand: Yakima Pages: 12
JEHNERT SOUND DESIGN 65400 Assembly Instruction Manual preview
65400
Brand: JEHNERT SOUND DESIGN Pages: 8
Rainbow Experience Series Installation Manual preview
Experience Series
Brand: Rainbow Pages: 19
Yakima K1006 Instructions Manual preview
K1006
Brand: Yakima Pages: 12
Vauxhall INSIGNIA 2017 Owner'S Manual preview
INSIGNIA 2017
Brand: Vauxhall Pages: 323
Kia 2016 Cadenza Owner'S Manual preview
2016 Cadenza
Brand: Kia Pages: 419
Club Car Gasoline/Electric DS Golf Car 1996 Owner'S Manual preview
Gasoline/Electric DS Golf Car 1996
Brand: Club Car Pages: 48
Kolpin Outdoors 25-1080 Assembly & Owners Manual preview
25-1080
Brand: Kolpin Outdoors Pages: 6
Schartec CR 4 Manual preview
CR 4
Brand: Schartec Pages: 2
muth signal mirror 2005-2009 Ford Mustang Installation Instruction preview
signal mirror 2005-2009 Ford Mustang
Brand: muth Pages: 9
Yescom YES5062 User Manual preview
YES5062
Brand: Yescom Pages: 4
Z Automotive Tazer DT User Manual preview
Tazer DT
Brand: Z Automotive Pages: 16
Motoalliance VIPER MA11922 Install Instructions Manual preview
VIPER MA11922
Brand: Motoalliance Pages: 8
Skoda OCTAVIA - TECHNICAL CHANGES 11-2009 Owner'S Manual Supplement preview
OCTAVIA - TECHNICAL CHANGES 11-2009
Brand: Skoda Pages: 16

Brands by name

Popular brands

Load more brands