Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 148 | Manualshive

Page: 148 / 440

background image

Illuminated Front Cupholders — If Equipped

The front cupholders are illuminated with LEDs. They
are turned on with the headlights or parking lights. Refer
to “Interior Lights” under “Lights” in Section 3.

Rear Cupholders

The rear seat cupholders are located in the center armrest
between the rear seats. The cupholders are positioned
forward in the armrest and side-by-side to provide
convenient access to beverage cans or bottles while
maintaining a resting place for the rear occupants’ el-
bows.

CONSOLE FEATURES

Sliding Center Console Armrest

The center console armrest slides forward with three
detents to provide flexibility for comfort, cupholder use,
and shifting ease.

Rear Cupholders

146

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
146
147
148
149
150
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Toyota Pages: 529

Brand: Yakima Pages: 11

Brand: Quadratec Pages: 8

Brand: Yakima Pages: 4

Brand: 3SIXT Pages: 12

10-8002-C11998B

Brand: Saleen Pages: 12

2013 Buick Verano

Brand: Buick Pages: 5

Brand: Farad Pages: 8

5TH GEN 4RUNNER

Brand: Victory 4x4 Pages: 5

Brand: Keith Pages: 2

1973 Crown Hardtop

Brand: Toyota Pages: 50

Brand: Toyota Pages: 371

Automotive 31006

Brand: KRAFTWERK Pages: 2

Brand: Webasto Pages: 18

Brand: Easee Pages: 12

Brand: Vauxhall Pages: 131

Brand: rough country Pages: 4

Brand: CSL Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands