Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 51 | Manualshive

Page: 51 / 440

background image

Airbag System Components

The airbag system consists of the following:

•

Occupant Restraint Controller (ORC)

•

Side Remote Acceleration Sensors

•

Side Door Pressure Sensors

•

Airbag Warning Light

•

Driver Airbag

•

Front Passenger Airbag

•

Supplemental Side Curtain Airbags above Side Win-
dows

•

Steering Wheel and Column

•

Instrument Panel

•

Interconnecting Wiring

•

Seat Belt Reminder Light

•

Knee Impact Bolsters

•

Front Acceleration Sensors

•

Driver and Front Passenger Seat Belt Pretensioners

How the Airbag System Works

•

The

Occupant Restraint Controller (ORC)

determines

if a frontal collision is severe enough to require the
airbags to inflate. The front airbag inflators are de-
signed to provide different rates of airbag inflation
from direction provided by the ORC. The ORC will not
detect rollover.

•

The ORC also determines if a side impact is severe
enough to deploy the supplemental side curtain airbag
as required for each type of impact.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

49

2

«
...
49
50
51
52
53
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Raven Pages: 24

Brand: Weather Guard Pages: 4

Brand: Hama Pages: 6

Brand: Vauxhall Pages: 323

Brand: Camcar Pages: 6

Brand: ABL Pages: 4

Brand: Edelbrock Pages: 1

Brand: FORM FIT Pages: 2

Brand: Honda Pages: 32

Brand: Whispbar Pages: 15

Brand: Metra Electronics Pages: 8

Brand: BMW Pages: 55

Brand: Whispbar Pages: 15

2010 Civic Sedan

Brand: Honda Pages: 390

Brand: Draw tite Pages: 4

Brand: EFILive Pages: 25

Brand: Master Tailgaters Pages: 10

Brand: Brodit Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands