Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 88

Page: 88 / 440

•

This downloaded phonebook cannot be edited or
deleted on the uconnect

威

phone. These can only be

edited on the cellular phone. The changes are trans-
ferred and updated to uconnect

威

phone on the next

phone connection.

Phonebook Download — Single Entry

If equipped and supported by your phone, uconnect

威

phone allows the user to download entries from their
phone via Bluetooth

威

. To use this feature, press the

PHONE button and say “Phonebook Download.” The
system prompts, “Ready to accept “V” card entry via
Bluetooth

威

…” The system is now ready to accept phone-

book entries from your phone using the Bluetooth

威

Object Exchange Profile (OBEX). Please see your phone
Owner’s Manual for specific instructions on how to send
these entries from your phone.

NOTE:

•

The phone handset must support Bluetooth

威

OBEX

transfers of phonebook entries to use this feature.

•

Some phones cannot send phonebook entries if they
are already connected to any system via Bluetooth

威

and you may see a message on the phone display that
the Bluetooth

威

link is busy. In this case, the user must

first disconnect or drop the Bluetooth

威

connection to

the uconnect

威

phone, and then send the address book

entry via Bluetooth

威

. Please see your phone Owner’s

Manual for specific instructions on how to drop the
Bluetooth

威

connection.

•

If the phonebook entry is longer than 24 characters, it
will only use the first 24 characters.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Search results

Summary of Contents for 2009 Challenger SRT8

Reviews:

Related manuals for 2009 Challenger SRT8

Brands by name

Popular brands

Dodge 2009 Challenger SRT8, Owner'S Manual

Search results

Summary of Contents for 2009 Challenger SRT8

Reviews:

Related manuals for 2009 Challenger SRT8

Brands by name

Popular brands