Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 118 | Manualshive

Page: 118 / 440

background image

Heated Seats

The driver seat and front passenger seat are heated. The
heaters provide the same heat level for both cushion and
seatback. The controls for each heater are located near the
bottom center of the instrument panel.

After turning the ignition ON, you can choose from High,
Low, or Off heat settings. Amber indicator lights in each
switch indicate the level of heat in use. Two indicator
lights will illuminate for High, one for Low, and none for
Off.

Press the switch once to select High-level heat-
ing. Press the switch a second time to select
Low-level heating. Press the switch a third time
to shut the heating elements Off.

If high level heating is selected, the system will automati-
cally switch to the low level after 30 minutes of continu-
ous operation. At that time, the number of indicators
illuminated changes from two to one, indicating the
change. Operation on the low setting also turns off
automatically after 30 minutes.

NOTE:

Once a heat setting is selected, heat will be felt

within two to five minutes.

Heated Seat Switch

116

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
116
117
118
119
120
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 2

Brand: Cadillac Pages: 494

Brand: Cadillac Pages: 500

Brand: Cadillac Pages: 40

Brand: Cadillac Pages: 432

Brand: Cadillac Pages: 338

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 438

Brand: Camoplast Pages: 60

Brand: Saab Pages: 10

Brand: FORM FIT Pages: 2

Brand: Pyle Pages: 4

MAGNUM RT Series

Brand: Raptor Series Pages: 6

PRIME DESIGN VRR-NV200

Brand: Safe Fleet Pages: 12

Hypercharger HYC 075

Brand: Alpitronic Pages: 64

Challenger 2013

Brand: Dodge Pages: 543

Brand: STARLANE Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands