Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 274 | Manualshive

Page: 274 / 440

background image

WARNING!

Never use the PARK position as a substitute for the
parking brake. Always apply the parking brake fully
when parked to guard against vehicle movement and
possible injury or damage.

WARNING!

•

Never leave children alone in a vehicle. Leaving
unattended children in a vehicle is dangerous for a
number of reasons. A child or others could be
seriously or fatally injured. Do not leave the key in
the ignition. A child could operate power win-
dows, other controls, or move the vehicle.

•

Be sure the parking brake is fully disengaged
before driving; failure to do so can lead to brake
failure and an accident.

BRAKE SYSTEM

Your vehicle is equipped with dual hydraulic
brake systems. If either of the two hydraulic
systems loses normal capability, the remaining
system will still function. There will be some

loss of overall braking effectiveness. This may be evident
by increased pedal travel during application, greater

Parking Brake

272

STARTING AND OPERATING

«
...
272
273
274
275
276
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Samsung Pages: 133

Brand: Baja Designs Pages: 6

Brand: Jabra Pages: 10

Electronic Parking Disc II

Brand: Jacob Jensen Pages: 28

V2 SUPERCHARGER

Brand: Tesla Pages: 9

Brand: TrailFX Pages: 6

Brand: Edelbrock Pages: 1

Brand: FORM FIT Pages: 2

Brand: Chevrolet Pages: 344

Brand: Prorack Pages: 15

Brand: Cadillac Pages: 20

Brand: Yakima Pages: 11

Brand: Mercedes-Benz Pages: 358

2014 Grand Cherokee SRT8

Brand: Jeep Pages: 596

Brand: Skoda Pages: 4

Brand: ULTIMATE SPEED Pages: 6

1506-PHX Cargo Plus

Brand: Ranger design Pages: 8

Brand: AUTOTECH Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands