Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 234 | Manualshive

Page: 234 / 440

background image

Mode Control

Use this control to choose from several
patterns of air distribution. You can
select either a primary mode as iden-
tified by the symbols on the control, or
a blend of two of these modes.

•

Panel

Air is directed through the outlets in the instrument
panel and the center console. These outlets can be

adjusted to direct airflow.

NOTE:

The center instrument panel outlets can be

aimed so that they are directed toward the rear seat
passengers for maximum airflow to the rear.

•

Bi-Level

Air is directed through the instrument panel, center
console and floor outlets.

NOTE:

For all settings except full cold or full hot, there

is a difference in temperature between the upper and
lower outlets. The warmer air flows to the floor outlets.
This feature gives improved comfort during sunny but
cool conditions.

•

Floor

Air is directed through the floor outlets with a
small amount flowing through the defrost and side

window demist outlets.

•

Mix

Air is directed through the floor, defrost, and side
window demist outlets. This setting works best in
cold or snowy conditions that require extra heat to

the windshield. This setting is good for maintaining
comfort while reducing moisture on the windshield.

232

UNDERSTANDING YOUR INSTRUMENT PANEL

«
...
232
233
234
235
236
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Mercedes-Benz Pages: 30

2004 Vibe Navigation System

Brand: Pontiac Pages: 44

Brand: Toro Pages: 24

Brand: GMC Pages: 120

Brand: Prime Tech Pages: 6

Brand: Road Ranger Pages: 22

Brand: Westfalia Pages: 10

Quantum Wash'n'Wipe N30208

Brand: National Cycle Pages: 12

Brand: Skoda Pages: 324

Brand: travall Pages: 4

Brand: RAM Pages: 148

Brand: Hamron Pages: 36

Brand: Menabo Pages: 8

Brand: Navman Pages: 10

BUSHMAN 15L ROADIE fridge Base console

Brand: Cruiser Consoles Pages: 6

Brand: Brink Pages: 12

Brand: Mercedes-Benz Pages: 357

VIEWLINE TEMPERATURE GAUGES

Brand: VDO Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands