background image

70 Series Landcruiser Console Specialists

2535 Toowoomba – Cecil Plains Road

Biddeston QLD 4401

Phone: 0419 784 590

Email: [email protected]

http://www.cruiserconsole.com.au

SPlastic Dash 76 Wagon / 79 Dual Cab & DPF Single Cab –

BUSHMAN 15L ROADIE fridge Base console Installation

Instructions  

 The Bushman 15L ROADIE fridge base console is suited to the Dual Cab & Wagon New Dash model and
Late 2016 onwards DPF Single Cab models. Please read these instructions carefully and consider if you
have the required skill and patience to fit this kit.
These consoles have been designed with minimal modifications to be done to the vehicle, but some are
necessary at your own discretion for the fridge to fit. These instructions suit 76 Wagon, 79 Dual Cab and the
Side Curtain Airbag 79 Single Cab though all consoles are model specific. 
No seat rail modifications are required for the Side Curtain Airbag Single Cabs.

 1. INTRODUCTION

Take note of the hole in the console under the vinyl in this
location (plastic dash only)

2. OEM CUPHOLDER REMOVAL

When fitting the new gearstick surround, remove the 3
bolts (as indicated in image) and the plastic trim clip from
the factory cup holder base. 2 of them have 10mm heads
and one has a 12mm head.

Page 1

Summary of Contents for BUSHMAN 15L ROADIE fridge Base console







Reviews: