Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 37 | Manualshive

Page: 37 / 440

background image

OCCUPANT RESTRAINTS

Some of the most important safety features in your
vehicle are the restraint systems. These include the front
and rear seat belts for the driver and all passengers, the
front airbags for both the driver and front passenger, and
the supplemental side curtain airbags for the driver and
passengers seated next to a window. If you will be
carrying children too small for adult-sized belts, your
seat belts also can be used to hold infant and child
restraint systems.

Please pay close attention to the information in this
section. It tells you how to use your restraint system
properly, to keep you and your passengers as safe as
possible.

WARNING!

In a collision, you and your passengers can suffer
much greater injuries if you are not properly buckled
up. You can strike the interior of your vehicle or other
passengers or you can be thrown out of the vehicle.
Always be sure you and others in your vehicle are
buckled up properly.

Buckle up even though you are an excellent driver, even
on short trips. Someone on the road may be a poor driver
and cause a collision that includes you. This can happen
far away from home or on your own street.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

35

2

«
...
35
36
37
38
39
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: ZAPTEC Pages: 240

CommCenter D1 Series

Brand: Federal Signal Corporation Pages: 16

Brand: Blue Ox Pages: 7

Brand: Shad Pages: 3

Brand: Whispbar Pages: 15

Brand: SuperATV Pages: 7

Brand: Park-Daddy Pages: 22

Brand: Brodit Pages: 2

Brand: Subaru Pages: 32

Brand: Rugged Ridge Pages: 2

Brand: TrailFX Pages: 2

iTrip Bluetooth

Brand: Griffin Technology Pages: 6

Pajero Pinin 1999

Brand: Mitsubishi Pages: 919

Brand: Acura Pages: 19

Brand: Ford Pages: 325

Brand: Maserati Pages: 37

Dual Clamp Spare Tire Mount

Brand: FACTORY UTV Pages: 2

Brand: Skyjacker Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands