Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 33 | Manualshive

Page: 33 / 440

background image

5. A single chime will indicate the completion of the
programming.

NOTE:

If you do not hear the chime, it means that the

system did not enter the programming mode and you
will need to repeat the procedure.

6. Repeat these steps if you want to return this feature to
its previous setting.

NOTE:

Use the Automatic Unlock Doors On Exit feature

in accordance with local laws.

WINDOWS

Power Windows

The window controls on the driver’s door control both of
the door windows.

There is a single window control on the passenger’s door
trim panel that operates the window on the passenger’s
door. The window controls will operate only when the
ignition switch is in the ON or ACC position.

Power Window Switches

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

31

2

«
...
31
32
33
34
35
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: iDataLink Pages: 9

Brand: Baja Designs Pages: 6

Brand: Oldsmobile Pages: 360

Stratus LHD 1997

Brand: Chrysler Pages: 1534

Brand: AC Schnitzer Pages: 16

Brand: Rati Pages: 2

Brand: FALCON RIDGE Pages: 7

Brand: Volvo Pages: 30

Brand: Skoda Pages: 165

Brand: Hudson Pages: 34

ULTIMATE SPEED 296713

Brand: walser Pages: 10

Brand: Mercedes-Benz Pages: 373

Brand: Demco Pages: 4

Brand: Westin Pages: 3

Brand: iSimple Pages: 8

Brand: v.link Pages: 15

Brand: Cequent Performance Products Pages: 18

Carnival MPV 2023

Brand: Kia Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands