Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 81

Page: 81 / 440

uconnect

姞

phone — IF EQUIPPED

NOTE: The sales code RER and REU radios contain an
integrated uconnect

威

phone. Refer to your “Navigation

User’s Manual” for uconnect

威

phone operating instruc-

tions for these radios. Radio sales code can be located
on the lower right corner of the Radio faceplate.

uconnect

威

phone is a voice-activated, hands-free, in-

vehicle communications system. uconnect

威

allows you to

dial a phone number with your cellular phone using
simple voice commands (e.g.,

⬙

Call”

“Mike”

”Work

⬙

Dial”

“248-555-1212

⬙

). Your cellular phone’s audio is

transmitted through your vehicle’s audio system; the
system will automatically mute your radio when using
the uconnect

威

phone.

NOTE:

The uconnect

威

phone requires a cellular phone

equipped with the Bluetooth

威 ⬙

Hands-Free Profile,

⬙

Ver-

sion 0.96 or higher. See the uconnect

威

website for sup-

ported phones.
For uconnect

威

customer support, visit the following

websites:

•

www.chrysler.com/uconnect

•

www.dodge.com/uconnect

•

www.jeep.com/uconnect

•

or call 1–877–855–8400

Slide-On-Rod Extender

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Search results

Summary of Contents for 2009 Challenger SRT8

Reviews:

Related manuals for 2009 Challenger SRT8

Brands by name

Popular brands

Dodge 2009 Challenger SRT8, Owner'S Manual

Search results

Summary of Contents for 2009 Challenger SRT8

Reviews:

Related manuals for 2009 Challenger SRT8

Brands by name

Popular brands