Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 126 | Manualshive

Page: 126 / 440

background image

High Beam/Low Beam Select Switch

Push the multifunction lever away from you to switch
the headlights to high beam. Pull the multifunction lever
toward you to switch the headlights back to low beam.

Flash-to-Pass

You can signal another vehicle with your headlights by
lightly pulling the multifunction lever toward you. This
will turn on the high beam headlights until the lever is
released.

Overhead Console Map/Reading Lights

These lights are mounted between the sun visors on the
overhead console. Each light is turned on by pressing the
lens. Press the lens a second time to turn off the light.
These lights also turn on when a door is opened, or when
the UNLOCK button on the Remote Keyless Entry (RKE)
transmitter is pressed, or when the dimmer control is
turned fully upward, past the second detent.

Interior Lights

The interior lights come on when a door is opened.

To protect the battery, the interior lights will turn off
automatically 10 minutes after the ignition switch is
moved to the LOCK position. This will occur if the
interior lights were switched on manually or are on

Overhead Console

124

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
124
125
126
127
128
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: JANE Pages: 21

Brand: Alpine Pages: 8

3-series convertible

Brand: BMW Pages: 98

Wireless Charging Station Universal

Brand: BMW Pages: 160

Brand: Victory 4x4 Pages: 13

Brand: Rati Pages: 2

Brand: Fab Fours Pages: 19

Brand: Yakima Pages: 9

Brand: Pontiac Pages: 20

Brand: Ford Pages: 15

Brand: Honda Pages: 3

Platinum Pro Plug-in

Brand: Haltech Pages: 20

Brand: Octocam Pages: 35

Brand: Chevrolet Pages: 406

Brand: RUSPA Pages: 5

Brand: SAN HIMA Pages: 8

Brand: Comtronics Pages: 18

Brand: Jeep Pages: 502

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands