Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 124 | Manualshive

Page: 124 / 440

background image

Daytime Running Lights — If Equipped

The high beam headlights will come on as Daytime
Running Lights whenever the ignition switch is ON, the
headlights are off, and the parking brake is off. The
headlight switch must be used for normal nighttime
driving.

Lights-On Reminder

If the headlights or parking lights are on after the ignition
is turned OFF, a chime will sound to alert the driver
when the driver’s door is opened.

Fog Lights

The front fog light switch is built into the head-
light switch. To activate the front fog lights, turn
on the parking lights or the low beam headlights

and press the headlight switch. To turn off the front fog
lights, either press the headlight switch again or turn off
the headlight switch.

An indicator light in the instrument cluster illuminates
when the fog lights are turned on.

NOTE:

The fog lights will operate with the low beam

headlights or parking lights on. However, selecting the
high beam headlights will turn off the fog lights.

122

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
122
123
124
125
126
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: GMC Pages: 20

Brand: Haibang Pages: 6

Brand: Gator Pages: 8

Brand: Ford Pages: 256

Brand: Westin Pages: 2

Brand: Thule Pages: 8

Brand: Tesla Pages: 42

Brand: Kargo Master Pages: 17

Brand: ULTIMATE SPEED Pages: 132

Brand: Ford Pages: 312

Giulia 952 2017

Brand: Alfa Romeo Pages: 324

Brand: Rhino-Rack Pages: 4

Brand: Dodge Pages: 439

Brand: Laser Pages: 23

Brand: FORM FIT Pages: 2

Brand: FORM FIT Pages: 2

Brand: FORM FIT Pages: 4

Brand: FORM FIT Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands