Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 27 | Manualshive

Page: 27 / 440

background image

2. Remove and replace the battery. When replacing the
battery, match the + sign on the battery to the + sign on
the inside of the battery clip, located on the back cover.
Avoid touching the new battery with your fingers. Skin
oils may cause battery deterioration. If you touch a
battery, clean it with rubbing alcohol.

3. To reassemble the RKE transmitter case, snap the two
halves of the case together. Make sure there is an even
“gap” between the two halves. If equipped, install and
tighten the screw until snug. Test RKE transmitter
operation.

General Information

This device complies with Part 15 of the FCC rules and
RSS 210 of Industry Canada. Operation is subject to the
following conditions:

•

This device may not cause harmful interference.

•

This device must accept any interference received,
including interference that may cause undesired
operation.

NOTE:

Changes or modifications not expressly ap-

proved by the party responsible for compliance could
void the user’s authority to operate the equipment.

If your RKE transmitter fails to operate from a normal
distance, check for these two conditions:

1. A weak battery in the transmitter. The expected life of
the battery is a minimum of three years.

2. Closeness to a radio transmitter such as a radio station
tower, airport transmitter, and some mobile or CB radios.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

25

2

«
...
25
26
27
28
29
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

UNIVERSAL CJ-2A

Brand: Jeep Pages: 27

Brand: Jeep Pages: 228

Brand: Jeep Pages: 108

Brand: Jeep Pages: 525

Brand: Volvo Pages: 24

Brand: Sears Pages: 41

Brand: Baja Designs Pages: 5

Brand: Road Ranger Pages: 22

Brand: travall Pages: 2

Brand: Gacell Pages: 12

Brand: TATA Motors Pages: 151

QUICKDRAW RACHET TIE-DOWNS 855

Brand: Thule Pages: 3

Brand: Bilstein Pages: 7

Brand: Porsche Pages: 146

XC70 - ANNEXE 808

Brand: Volvo Pages: 8

Brand: Prime Design Pages: 12

Brand: Menabo Pages: 8

Brand: Audiovox Electronics Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands