Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 38 | Manualshive

Page: 38 / 440

background image

Research has shown that seat belts save lives, and they
can reduce the seriousness of injuries in a collision. Some
of the worst injuries happen when people are thrown
from the vehicle. Seat belts reduce the possibility of
ejection and the risk of injury caused by striking the
inside of the vehicle.

Everyone

in a motor vehicle should

be belted at all times.

Lap/Shoulder Belts

All seating positions in your vehicle are equipped with
lap/shoulder belts.

The belt webbing retractor is designed to lock during
very sudden stops or impacts. This feature allows the
shoulder part of the belt to move freely with you under
normal conditions. However, in a collision, the belt will
lock and reduce your risk of striking the inside of the
vehicle or being thrown out.

WARNING!

•

It is extremely dangerous to ride in a cargo area,
inside or outside of a vehicle. In a collision, people
riding in these areas are more likely to be seri-
ously injured or killed.

•

Do not allow people to ride in any area of your
vehicle that is not equipped with seats and seat
belts.

•

Be sure everyone in your vehicle is in a seat and
using a seat belt properly.

•

Wearing a seat belt incorrectly is dangerous. Seat
belts are designed to go around the large bones of
your body. These are the strongest parts of your
body and can take the forces of a collision best.

(Continued)

36

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
36
37
38
39
40
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: B-Speech Pages: 18

Brand: Taffio Pages: 8

Brand: Metra Electronics Pages: 12

Brand: Halfords Pages: 4

Brand: Porsche Pages: 195

Brand: Doug Thorley Headers Pages: 5

Brand: Edelbrock Pages: 2

2016 Sandero Stepway

Brand: Renault Pages: 183

Brand: Jeep Pages: 380

Brand: BMW Pages: 38

Brand: ideus Pages: 159

Sedan CIVIC 2022

Brand: Honda Pages: 701

Brand: Flash Cover Pages: 2

Brand: Porsche Pages: 98

2000 Oldsmobile Intrigue

Brand: Oldsmobile Pages: 348

Brand: S3 Power Sports Pages: 2

2004 Impreza OUTBACK SPORT

Brand: Subaru Pages: 34

Brand: Air Lift Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands