Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 347 | Manualshive

Page: 347 / 440

background image

Engine Oil Filter Selection

This manufacturer’s engines have a full-flow type oil
filter. Use a filter of this type for replacement. The quality
of replacement filters varies considerably. Only high
quality filters should be used to assure most efficient
service. MOPAR

威

engine oil filters are a high quality oil

filter and are recommended.

Engine Air Cleaner Filter

Refer to the “Maintenance Schedule” in Section 8 for the
proper maintenance intervals.

WARNING!

The air induction system (air cleaner, hoses, etc.) can
provide a measure of protection in the case of engine
backfire. Do not remove the air induction system (air
cleaner, hoses, etc.) unless such removal is necessary
for repair or maintenance. Make sure that no one is
near the engine compartment before starting the
vehicle with the air induction system (air cleaner,
hoses, etc.) removed. Failure to do so can result in
serious personal injury.

Engine Air Cleaner Filter Selection

The quality of replacement engine air cleaner filters varies
considerably. Only high quality filters should be used to
assure most efficient service. MOPAR

威

engine air cleaner

filters are a high quality filter and are recommended.

MAINTAINING YOUR VEHICLE

345

7

«
...
345
346
347
348
349
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Camoplast Pages: 60

Brand: Yakima Pages: 12

Brand: JEHNERT SOUND DESIGN Pages: 8

Experience Series

Brand: Rainbow Pages: 19

Brand: Yakima Pages: 12

Brand: Westin Pages: 3

Wallbox eM4 Single

Brand: ABL Pages: 68

Brand: Subaru Pages: 3

Brand: Haibang Pages: 6

Brand: ECS Electronics Pages: 16

Brand: Whispbar Pages: 17

Brand: Mercedes-Benz Pages: 358

Brand: ULTIMATE SPEED Pages: 34

Interlock 700 Series

Brand: Scania Pages: 82

Brand: r.LiNK Pages: 20

Brand: Huf Pages: 6

LockNLoad LightenUp

Brand: Yakima Pages: 13

viano 639 series

Brand: Mercedes-Benz Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands