Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 44 | Manualshive

Page: 44 / 440

background image

Use Reminder System (BeltAlert

威

) will alert the driver to

buckle the seat belt. The driver should also instruct all
other occupants to buckle their seat belts. Once the
warning is triggered, the BeltAlert

威

will continue to

chime and flash the Seat Belt Reminder Light for 96 sec-
onds or until the driver’s seat belt is buckled. The
BeltAlert

威

will be reactivated if the driver’s seat belt is

unbuckled for more than 10 seconds and the vehicle
speed is greater than 5 mph (8 km/h).

BeltAlert

威

Programming

The BeltAlert

威

can be enabled or disabled by your

authorized dealer or by performing the following steps:

NOTE:

Chrysler LLC does not recommend deactivating

the BeltAlert

威

.

1. With both doors closed, and the ignition switch in any
position except ON or START, buckle the driver’s seat
belt.

2. Turn the ignition switch to the ON position, but do not
start the engine. Wait for the Seat Belt Reminder Light to
turn off and then proceed to the next step.

NOTE:

You must perform the following steps within

60 seconds of turning the ignition switch to the ON
position.

3. Within 60 seconds of turning the ignition switch to the
ON position, unbuckle and then re-buckle the driver’s
seat belt at least three times, ending with the seat belt
buckled.

NOTE:

Watch for the Seat Belt Reminder Light to turn

on while unbuckling the seat belt and turn off while
re-buckling the seat belt. It may be necessary to retract
the seat belt.

4. Turn the ignition switch to the LOCK position. A
single chime will sound to signify that you have success-
fully completed the programming.

42

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
42
43
44
45
46
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Kargo Master Pages: 5

UNIVERSAL CJ-2A

Brand: Jeep Pages: 27

Brand: Jeep Pages: 228

Brand: Jeep Pages: 108

Brand: Jeep Pages: 525

Brand: Axxess Pages: 8

Brand: SeaSucker Pages: 9

Brand: EUFAB Pages: 16

Brand: Sanitas Pages: 36

Brand: Honda Pages: 22

Brand: Mercedes-Benz Pages: 494

Security Cage Kit

Brand: Toro Pages: 8

Brand: Peiying Pages: 32

Brand: Menabo Pages: 8

MAGIC WATCH MWE-850-4XXL

Brand: Waeco Pages: 228

Tipper Remote Kit

Brand: Nugent Pages: 21

MagicWatch MWE150

Brand: Waeco Pages: 176

Brand: Yakima Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands