Dodge 2009 Challenger SRT8 Owner'S Manual Download Page 80 | Manualshive

Page: 80 / 440

background image

Illuminated Vanity Mirrors

An illuminated vanity mirror is located on the sun visor.
To use the mirror, rotate the sun visor downward and
swing the mirror cover upward. The light turns on
automatically. Close the mirror cover to turn off the light.

Slide-On-Rod and Extender Features of Sun Visor

To use the slide-on-rod feature of the sun visor, rotate the
sun visor downward and swing the sun visor so it is
parallel to the side window, grabbing the sun visor with
your left hand pull rearwards until the sun visor is in the
desired position. To use the extender feature of the sun
visor, grab the extender which is located at the rear of the
visor and pull rearward.

Illuminated Vanity Mirror

78

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
78
79
80
81
82
...
»

Summary of Contents for 2009 Challenger SRT8

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2009 Challenger SRT8

Brand: Daihatsu Pages: 41

Brand: Daihatsu Pages: 268

Brand: GMC Pages: 499

Brand: Kia Pages: 290

Brand: Trailboss Pages: 8

Brand: SnapPad Pages: 5

Brand: EEZ RV Pages: 31

Brand: STC Pages: 6

Brand: Ford Pages: 368

Brand: RAM Pages: 496

OCTAVIA - TECHNICAL CHANGES 11-2009

Brand: Skoda Pages: 16

Brand: Paser Pages: 2

Brand: Xblitz Pages: 56

Brand: Mercedes-Benz Pages: 296

2000 9-5 2.3 Turbo Ecopower

Brand: Saab Pages: 256

Jumpy Miltispace

Brand: CITROËN Pages: 164

Brand: Directed Pages: 30

Brand: CSL Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands