Buffalo TeraStation WSS 5000 User Manual Download Page 222

Page: 222 / 229

221

LCD Message

Description

Corrective Action

RAID I18
ARRAYx Rebuilding

Rebuilding RAID array x.

Note:

Transfer speeds are slower during

the rebuilding process.

RAID I19
ARRAYx 0 Filling

Writing 0s to RAID array x, erasing all
data.

RAID I20
DISKx Formatting

Formatting hard drive x.

RAID I21
DISKx Checking

Checking hard drive x.

RAID I22
DISKx 0 Filling

Erasing the data for hard drive x.

SYSTEM I25
F/WUPDATING

Updating the TeraStation firmware.

Note:

Do not turn off the power during

the updating process.

Web Setting I26
Initializing

Initializing all settings.

USB Diskx I27
Checking

Checking USB hard drive x.

USB Diskx I28
Formatting

Formatting USB hard drive x.

Press FuncSW I31
New Diskx ready

Displayed when pressing the Function
button to rebuild the RAID after replacing
hard drive x.

Press the Function button to rebuild the
RAID array.

Set From Web I32
New Diskx ready

Displayed after replacing hard drive x
when the RAID needs to be rebuilt in
Settings or formatting is necessary.

In Settings, either rebuild the RAID array or
format the hard drive.

Replication I33
ReplicateFailure

An error occurred in replication, or
synchronization between the main
TeraStation and the backup TeraStation
failed during failover configuration.

In Settings, navigate to

Backup

Replication

and choose "Resync" to execute
resynchronization. If the error is displayed
again, contact Buffalo technical support for
assistance.

Virus alert I34
Virus detected

A virus scan found a virus.

Once the virus is removed from the
quarantine folder, the message is no
longer displayed. If the antivirus software
is configured to delete viruses from the
quarantine folder automatically, then the
message will not be displayed.

Cartridgex I35
Location error

A hard drive set as a media cartridge has
been installed in the drive x slot.

Connect to the slot that was set as a media
cartridge.

Cartridgex I36
Decryption error

Media cartridge cannot be decrypted.
The media cartridge may have been
encrypted by a TeraStation other than
this product.

Connect to the TeraStation that performed
encryption to decrypt.

Recovery I37
SystemRecovering

System recovery in progress.

Recovery I38
RecoveryFinished

System recovery is complete.

Recovery I39
Change Boot

System recovery from the USB recovery
device is complete.

Change the boot mode switch on the rear
to HDD.

Recovery I40
DataWillDeleted

Beginning recovery. All data in the drive 1
will be deleted.

Recovery I41
PushFuncToStart

Pressing the function button on the front
will start the recovery process.

Summary of Contents for TeraStation WSS 5000






































































































































































































































Search results

Summary of Contents for TeraStation WSS 5000

Reviews:

Related manuals for TeraStation WSS 5000

Brands by name

Popular brands

Buffalo TeraStation WSS 5000, User Manual

Search results

Summary of Contents for TeraStation WSS 5000

Reviews:

Related manuals for TeraStation WSS 5000

Brands by name

Popular brands