Bosch DS7200V2-UK Installer'S Manual Download Page 67 | Manualshive

Page: 67 / 142

background image

DS7200V2-UK Installer's Guide

Copyright



2007 Bosch Security Systems, Inc.

P/N: 4998152533-02 Page 67

PART IV: CONTROL PANEL PROGRAMMING

39.0 Keypads

Wired Keypads 1 to 8 are fixed at Data Bus Addresses 1 to 8. All keypads (and other Data Bus devices) are fully supervised.
Supervision reports (missing, tamper, etc.) follow the System Status Report routing.

The settings listed in this column are the address jumper pins that must be covered by a jumper plug. See Keypad Addressing
on page 14 for more information.

Keypad #/Door Access Control Module (DACM) Area Options

•

Address:

−

Keypad/DACM 1: 0679

−

Keypad/DACM 2: 0681

−

Keypad/DACM 3: 0683

−

Keypad/DACM 4: 0685

−

Keypad/DACM 5: 0687

−

Keypad/DACM 6: 0689

−

Keypad/DACM 7: 0691

−

Keypad/DACM 8: 0693

•

Default:

−

Keypad 1/DACM: 1 (Device is a keypad/DACM assigned to Area 1)

−

Keypad/DACM 2-8: 0 (No keypad/DACM assigned - disabled)

•

Selections: 0-4, 9-12

Enter This Data Digit to Select Options

Keypad/DACM Area Options

0

1

2

3

4

5

6

7

8

9 10 11 12 13 14 15

Keypad/DACM not assigned (disabled)

•

Assign Keypad/DACM to Area 1

•

•

Assign Keypad/DACM to Area 2

•

•

Assign Keypad/DACM to Area 3 (DS7240V2 only)

•

•

Assign Keypad/DACM to Area 4 (DS7240V2 only)

•

•

Device is a Keypad

•

•

•

•

Device is a DACM

•

•

•

•

Assign only one area to each keypad. Users (PINs) can be assigned to multiple areas.

The Move to Area function ([#][5][0]) allows users (PINs) assigned to multiple areas to view those areas from one keypad.

The control panel supervises the connection to the DACM. If it fails to communicate with the control panel, the control panel
sends a “DBus Missing” {125} report. See DACM Configuration on page 116 for more information.

See the documentation supplied with the DACM for complete installation, programming, addressing, and operation
instructions.

The control panel supports up to 8 DACMs. However, each DACM added to the system replaces one keypad. If 8
DACMs are added, you cannot add a keypad. For full system control, make sure at least one text keypad is
included in the system.

«
...
65
66
67
68
69
...
»

Summary of Contents for DS7200V2-UK















































































































































Reviews:

No comments

Related manuals for DS7200V2-UK

Brand: GE Pages: 425

Brand: T-Verter Pages: 121

Brand: Happy Pages: 10

Brand: Samson Pages: 36

Brand: FBII Pages: 71

Brand: CAME Pages: 4

Brand: Rain Bird Pages: 48

Brand: Icom Pages: 30

Brand: ICM Controls Pages: 2

Brand: ICM Controls Pages: 2

Brand: ray Pages: 11

Brand: PACH & COMPANY Pages: 4

Brand: M-system Pages: 13

MT600iWP Series

Brand: weintek Pages: 2

Brand: I-Tork Pages: 15

Brand: MGC Pages: 16

Brand: Roger Pages: 21

Saxun Mosquito Screen Lateral Door 2020

Brand: Gimenez Ganga Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands