Bosch DS7200V2-UK Installer'S Manual Download Page 29

Page: 29 / 142

DS7200V2-UK Installer's Guide



2007 Bosch Security Systems, Inc.

P/N: 4998152533-02 Page 29

PART II: SYSTEM INSTALLATION AND SETUP

Use the following steps to install a DX4020 in the
CX1011 Enclosure:

1. Mount the DX4020 to the B234 Angle Bracket

(sold separately) using the screws supplied with
the DX4020. See Figure 47.

Back of B234

Angle Bracket

Back of DX4020

Screws supplied

with DX4020

Figure 47: Mounting the DX4020 (Step 1)

2. Insert the B234’s hooks into the mounting slots

in the back wall of the CX1011 Enclosure. See
Figure 48.

Hook

Slot

Screw Hole

Enclosure Back Wall

Back of DX4020

Back of B234

Angle Bracket

Figure 48: Mounting the DX4020 (Step 2)

3. Pull the B234 down so that its hooks are flush

in the mounting slots. See Figure 49.

Hooks flush

with Slots

Back of DX4020

Screw Hole

Enclosure Back Wall

Back of B234

Angle Bracket

Figure 49: Mounting the DX4020 (Step 3)

4. Secure the B234 to the CX1011 enclosure wall

with the screw supplied with the B234. See
Figure 50

Enclosure Back Wall

Mounting Screw

Front of B234

Angle Bracket

Front of

DX4020

Figure 50: Mounting the DX4020 (Step 4)

Summary of Contents for DS7200V2-UK














































































































































Search results

Summary of Contents for DS7200V2-UK

Reviews:

Related manuals for DS7200V2-UK

Brands by name

Popular brands

Bosch DS7200V2-UK, Installer'S Manual

Search results

Summary of Contents for DS7200V2-UK

Reviews:

Related manuals for DS7200V2-UK

Brands by name

Popular brands