Bosch DS7200V2-UK Installer'S Manual Download Page 10 | Manualshive

Page: 10 / 142

background image

Page 10 P/N: 4998152533-02

Copyright



2007 Bosch Security Systems, Inc.

DS7200V2-UK Installer's Guide

PART I: INTRODUCTION

6.3 RF

Devices

•

RF3227E RF Receiver: Supervises the use of

wireless devices. Up to 2 allowed per system.

•

RF3332E RF Keyfob: 2-button keyfob that can

arm/disarm the system and send a Panic code to
the Security Company if programmed.

•

RF3334E RF Keyfob: 4-button keyfob that can

arm/disarm the system and send a Panic code to
the Security Company if programmed. It can also
control other devices.

•

RF3401E Point Transmitter: Point transmitter that

features a supervised sensor loop and a magnetic
reed switch. External magnet assembly allows for
quick and easy installation on doors and windows.

•

RF3405E Inertia Transmitter: Magnetic and dry

contact wireless transmitter with a built-in inertia
sensor used for monitoring doors, windows, or other
dry contact devices.

•

RF3503E Two-Button Transmitter: Magnetic and

dry contact wireless transmitter with a built-in inertia
sensor. Used for monitoring doors, windows, or
other dry contact devices.

•

RF1100E Glassbreak Detector: Wireless

transmitter used for detecting breaking glass.

•

RF280ETHS Wireless Smoke Detector: Wireless

photoelectric smoke detector with built-in 135°F
(57°C) heat sensor and 85 dB sounder.

•

RF835E Wireless TriTech PRI/Microwave

Detector: Wireless detector that utilizes passive
infrared (PIR) technology, microwave (MW)
technology, and artificial intelligence to detect
motion.

•

RF940E Wireless PIR Detector: High performance

PIR motion sensor.

6.4 Programming

Tools

•

DS7447E/DS7447V2 Text Keypad: Required for

keypad programming.

•

PK32 Programming Key: Copy system

programming entries to key for quick delivery to
another system. Can also be used as a backup disk.

•

Remote Programming Software (RPS): Remote

programming and account management utility.

7.0 System

Batteries

7.1 Standby

Battery

•

12 V, 7 Ah sealed lead-acid rechargeable battery

•

Power Sonic: PS-1270

•

YUASA: NP7-12

7.2 RAM

Backup

Battery

•

3 V coin-type lithium battery (Panasonic CR2032 or

equivalent)

8.0 Available

Power

8.1 Auxiliary

Power

Use auxiliary power terminals to power devices
requiring continuous power. Up to 1.2 A is available
for continuously powered devices.

8.2 Alarm

Power

The Alarm Power (ALRM +) terminal provides positive
12 VDC for Programmable Output 2 (PO 2) when it is
configured as a siren driver, and PO 1 when it is
configured as the alarm output. Up to 1.85 A of alarm
power is available.

9.0 Installer

Keypad

Connector

Use the Aux/Data connector to connect an Installer
Keypad or a DX4010i/DX4010 to the control panel for
programming and diagnostics.

«
...
8
9
10
11
12
...
»

Summary of Contents for DS7200V2-UK















































































































































Reviews:

No comments

Related manuals for DS7200V2-UK

Brand: D-Link Pages: 113

Brand: D-Link Pages: 146

Brand: Echelon Pages: 40

Brand: Campbell Pages: 8

Brand: Danfoss Pages: 7

Brand: Danfoss Pages: 32

PVG 16 PVH/Covers

Brand: Danfoss Pages: 112

Brand: Danfoss Pages: 44

PVG 16 PVH/Covers

Brand: Danfoss Pages: 144

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 64

Brand: Danfoss Pages: 8

VLT AutomationDrive FC 360

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 6

Brand: Danfoss Pages: 4

Brand: Danfoss Pages: 8

Brand: Danfoss Pages: 2

ECL Comfort 110

Brand: Danfoss Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands