Bosch DS7200V2-UK Installer'S Manual Download Page 99 | Manualshive

Page: 99 / 142

background image

DS7200V2-UK Installer's Guide

Copyright



2007 Bosch Security Systems, Inc.

P/N: 4998152533-02 Page 99

PART IV: CONTROL PANEL PROGRAMMING

48.0 RS-232 Module Configuration

The following parameters apply to the DX4010i and DX4010 RS-232 Serial Interface Modules.

Output Configuration Options

•

Address: 1253

•

Default: 0 (Disabled)

•

Selections:

−

0 = Disabled(no RS-232 module connected)

−

1 = RS-232 Log Output using Internal Codes

−

2 = RS-232 Log Output using PC Compatible Codes

Set the module to Data Bus Address 250. See DX4010i/DX4010 Addressing on page 27 for information.

This parameter only applies when the module is used for RS-232 serial output. It does not apply if the module is used for
direct-connect local programming.

•

RS-232 Log Output using Internal Codes: If enabled, this option outputs the events using the internal keypad character

codes. Non-standard characters may not print correctly.

•

RS-232 Log Output using PC Compatible Codes: If enabled, this option outputs the events using PC compatible

character codes. Non-standard characters are mapped to the closest matching character for display or printing.

If you connect a printer to the module and get unexpected results, check the module output
configuration (Address 1253), baud rate configuration (Address 1254) and parity/flow control/stop bit
configuration (Address 1255) for proper settings.

Baud Rate Options

•

Address: 1254

•

Default: 2 (2400 bps)

•

Selections:

−

1 = 1200 bps

−

2 = 2400 bps

−

3 = 4800 bps

−

4 = 9600 bps

−

5 = 14400 bps

This parameter identifies which baud rate the module should use for communication.

If you connect a printer to the module and get unexpected results, check the module output
configuration (Address 1253), baud rate configuration (Address 1254) and parity/flow control/stop bit
configuration (Address 1255) for proper settings.

«
...
97
98
99
100
101
...
»

Summary of Contents for DS7200V2-UK















































































































































Reviews:

No comments

Related manuals for DS7200V2-UK

ControlMaster CM15

Brand: ABB Pages: 28

Brand: Ohsung Electronics Pages: 18

Brand: UNITED Pages: 8

Brand: Danfoss Pages: 7

Brand: Lawler Pages: 4

Brand: Hama Pages: 46

Brand: Galcon Pages: 35

Brand: Ebyte Pages: 38

Brand: EBS Pages: 30

Brand: FATEK Pages: 10

Brand: Rain Bird Pages: 20

Brand: WAREMA Pages: 112

Brand: WAGO Pages: 414

Brand: V2 Pages: 48

Brand: RadioMaster Pages: 10

Brand: Xblue Networks Pages: 2

Brand: ABB Pages: 17

Brand: DSE Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands