Bosch DS7200V2-UK Installer'S Manual Download Page 23

Page: 23 / 142

DS7200V2-UK Installer's Guide



2007 Bosch Security Systems, Inc.

P/N: 4998152533-02 Page 23

PART II: SYSTEM INSTALLATION AND SETUP

19.4 DX3013

Installation

The DX3010 contains static-sensitive
components and must be handled with care.
Follow anti-static procedures when handling
this module.

You can install a maximum of two DX3013 modules
(DX3010 mounted on an angle bracket) in the
DS7240V2’s enclosure. Only 1 DX3010 can be
connected to the DS7220V2.

See Figure 29 for mounting locations.

DX3013 Mounting Locations

INSTALLER

PO4

PO3

PO2

Figure 29: DX3013 Mounting Locations

Use the following steps to install a DX3013 in the
CX1011 Enclosure:

1. Insert the DX3013’s angle bracket hooks into the

mounting slots in the back wall of the CX1011
Enclosure. See Figure 30.

Hook

Slot

Screw Hole

Enclosure Back Wall

Back of DX3013

Mounting Plate

Back of

Angle Bracket

Figure 30: Mounting the DX3013 (Step 1)

2. Pull the DX3013 down so that the angle bracket

hooks are flush in the mounting slots. See Figure
31.

Hooks flush

with Slots

Back of DX3013

Mounting Plate

Screw Hole

Enclosure Back Wall

Back of

Angle Bracket

Figure 31: Mounting the DX3013 (Step 2)

Summary of Contents for DS7200V2-UK














































































































































Search results

Summary of Contents for DS7200V2-UK

Reviews:

Related manuals for DS7200V2-UK

Brands by name

Popular brands

Bosch DS7200V2-UK, Installer'S Manual

Search results

Summary of Contents for DS7200V2-UK

Reviews:

Related manuals for DS7200V2-UK

Brands by name

Popular brands