Bosch DS7200V2-UK Installer'S Manual Download Page 113 | Manualshive

Page: 113 / 142

background image

DS7200V2-UK Installer's Guide

Copyright



2007 Bosch Security Systems, Inc.

P/N: 4998152533-02 Page 113

PART IV: CONTROL PANEL PROGRAMMING

Format for Destination 1 (2)

•

Address:

−

Format for Destination 1: 0064

−

Format for Destination 2: 0130

•

Default: 2 (Contact ID)

•

Selections:

−

2 = Contact ID

−

3 = SIA 300

−

4 = Basic Pager

−

6 = BSIA Fast Format

−

7 = Personal Dialing Format

−

11 = SIA 300 with Text Blocks

If you enable network communication, the control panel automatically selects Contact ID as the reporting format. Contact ID
only supports four-digit account numbers. As a result, the control panel automatically truncates account numbers to four digits.

Alternate Communication Options

•

Address Range:

−

IP Address 1, Destination 1: 3506

−

IP Address 2, Destination 1: 3514

−

IP Address 1, Destination 2: 3522

−

IP Address 2, Destination 2: 3530

•

Default: 0

•

Selections: 0, 1, 3, 5, 7

Enter This Data Digit to Select Options

Alternate Communication Options

0

1

2

3

4

5

6

7

8

9 10 11 12 13 14 15

No Alternate Communication

•

Enable Alternate Communication

•

•

•

•

Enable Anti-Replay

•

•

Use ARC Acks

•

•

Reserved

•

Enable Alternate Communication: Select this option to enable network communication. You must enter at least one IP

address as a routing destination. See IP Address 1 (2) for Destination 1 (2) on page 112 for more information.

•

Enable Anti-Replay: Anti-replay prevents unauthorized messages from being sent to the ARC and being recognized as

having originated from the control panel. Enable this option to use the anti-replay procedure. To use this option, make sure
“Include IP Address” is enabled in Network Interface Module Options on page 115.

•

Use ARC Acks: If this option is enabled, the control panel waits for an acknowledgment (Ack) from the ARC before sending

a second message. If this option is disabled, the control panel waits approximately 120 seconds between sending messages
(disable only for special applications).

Remote Programming Callback Number Alternate Communication Options

•

Address: 3538

•

Default: 0

•

Selections:

−

0 = No Alternate Communication

−

1 = Enabled Alternate Communication

If an IP address is entered into the Remote Programming Callback Number addresses (Addresses 0181-0212), RPS can be
used to program the control panel over an Ethernet network.

Select “1” if an IP address is entered in the Remote Programming Callback Number addresses.

«
...
111
112
113
114
115
...
»

Summary of Contents for DS7200V2-UK















































































































































Reviews:

No comments

Related manuals for DS7200V2-UK

Evolution Series E9000

Brand: GE Pages: 44

PACSystems RX7i

Brand: GE Pages: 469

GuardSwitch 300 Series

Brand: GE Pages: 2

GuardSwitch 300 Series

Brand: GE Pages: 2

Masoneilan VariPak 28001

Brand: GE Pages: 24

Brand: Waters Pages: 55

Brand: Paradox Pages: 2

Brand: D+H Pages: 36

Brand: D-Box Pages: 4

Brand: D+H Pages: 36

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 20

Brand: Daktronics Pages: 5

Brand: Daikin Pages: 12

Brand: Data I/O Pages: 88

Brand: Data Aire Pages: 13

Brand: RADEMACHER Pages: 68

Brand: D&R ELECTRONICS Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands