Avaya J100 Series Installing And Administering Download Page 61

Page: 61 / 528

System parameter
name

TLV name

Impact

L2Q, L2QVLAN

TIA LLDP MED
Network Policy
(Voice Signaling)

L2Q - set to 2 (off) if T (the Tagged Flag) is set to 0 and to 1
(on) if T is set to 1.

L2QVLAN - Set to the VLAN ID in the TLV.

L2QAUD - Set to the Layer 2 Priority value in the TLV.

DSCPAUD - Set to the DSCP value in the TLV.

A check is made as to whether a reset is necessary to obtain a
new IP address due to a change in the values of the
parameters L2Q or L2QVLAN.

This TLV is ignored if:

• The value of USE_DHCP is 0 and the value of IPADD is not

0.0.0.0.

• The Application Type is not 1 (Voice) or 2 (Voice Signaling).

• The Unknown Policy Flag (U) is set to 1.

SIP_CONTROLL
ER_LIST

Proprietary Call
Server TLV

SIP_CONTROLLER_LIST will be set to the IP addresses in
this TLV value.

Note:

This parameter cannot be used in an environment where
both SIP phones and H.323 phones exist.

TLSSRVR and
HTTPSRVR

Proprietary File
Server TLV

L2Q

Proprietary 802.1 Q
Framing

If the value of TLV = 1, L2Q is set to 1 (On).

If the value of TLV = 2, L2Q is set to 2 (Off).

If the value of TLV = 3, L2Q is set to 0 (Auto).

A check is made as to whether a reset is necessary to obtain a
new IP address due to a change in the values of the
parameters L2Q or L2QVLAN.

This TLV is ignored if:

• The value of USE_DHCP is 0 and the value of IPADD is not

0.0.0.0.

• The current L2QVLAN value was set by an IEEE 802.1

VLAN name.

• The current L2QVLAN value was set by a TIA LLDP MED

Network Policy (Voice) TLV.

Configuration through LLDP

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 61 / 528

Search results

Summary of Contents for J100 Series

Reviews: