manualshive.com logo in svg

Avaya J100 Series, Installing And Administering, Page: 308 / 528

Share
Download
Avaya J100 Series Installing And Administering Download Page 308

Parameter name

Default value

Description

BLF_INCOMING_CALL_INDICATION_MODE

3

Specifies the indication
mode for a BLF incoming
call.

Valid values:

• 0 - None (no alerting for

BLF incoming call).

• 1 - Audible (only audible

alerting for BLF
incoming call).

• 2 - Visual (only visual

alerting for BLF
incoming call).

• 3 - Both (both audible

and visual alerting for
BLF incoming call)

• 4 - Force None (forced

only audible alerting for
BLF incoming call).

• 5 - Force Audible (forced

only audible alerting for
BLF incoming call).

• 6 - Force Visual (forced

only visual alerting for
BLF incoming call).

• 7 - Force Both (forced

both audible and visual
alerting for BLF
incoming call).

Note:

This parameter is
supported only in the
3PCC environment.

Avaya J129 IP Phone
does not support this
feature.

Table continues…

Customizable parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

308

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Reviews:

No comments