Avaya J100 Series Installing And Administering Download Page 380

Page: 380 / 528

Parameter name

Default value

Description

L2QAUD

Specifies the layer 2
priority value for audio
frames generated by the
telephone.

Valid values are 0 through
7.

Note:

This parameter can
also be set through:

• SET command in a

settings file

• LLDP. Setting this

parameter though
LLDP overwrites
any values in the
settings file.

L2QSIG

Specifies the layer 2
priority value for signaling
frames generated by the
phone.

Valid values are 0 through
7.

Note:

This parameter can
also be set through:

• SET command in a

settings file

• LLDP

• AADS

Setting this
parameter through
LLDP or AADS
overwrites values in
the settings file.

Table continues…

Customizable parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

380

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 380 / 528

Search results

Summary of Contents for J100 Series

Reviews: