Avaya J100 Series Installing And Administering Download Page 452

Page: 452 / 528

Parameter name

Default value

Description

SIP Transport UDP

Determines whether SIP
Transport = UDP can be
manually configured on
the phone.

Valid values are:

• 0 for No

• 1 for Yes

Note:

This parameter is
supported for 3PCC
environment.

SIPCONFERENCECONTINUE

Specifies if a conference
call continues after the
host hangs up.

Value operation:

• 0: Drop all parties.

• 1: Continue conference

Note:

This parameter is set to 1
in IP Office environment.

SIPDOMAIN

Null

Specifies the domain
name to be used during
SIP registration.

The value can contain 0 to
255 characters. The
default value is null.

SIPPORT

5,060

Specifies the port the
phone opens to receive
SIP signaling messages.

Valid values are 1,024
through 65,535. The
default value is 5,060.

Table continues…

Customizable parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

452

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 452 / 528

Search results

Summary of Contents for J100 Series

Reviews: