Avaya J100 Series Installing And Administering Download Page 435

Page: 435 / 528

Parameter name

Default value

Description

RTCPMONPERIOD

Specifies the interval, in
seconds, for sending out
RTCP monitoring reports.
Valid values are from 5 to
30 seconds.

RTCPMONPORT

5,005

Specifies the RTCP
monitor port number.

You can set this parameter
only if the environment is
not an Avaya environment.
The values can range from
0 through 65,535. Default
is 5,005.

RTP_PORT_LOW

5,004

Specifies the lower limit of
the UDP port range to be
used by RTP or RTCP
connections.

The values can range from
1,024 through 65,503.

RTP_PORT_RANGE

Specifies the range or
number of UDP ports
available for RTP or RTCP
connections

This value is added to
RTP_PORT_LOW to
determine the upper limit
of the UDP port range.

The values can range from
32 through 64,511.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

435

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 435 / 528

Search results

Summary of Contents for J100 Series

Reviews: