Avaya J100 Series Installing And Administering Download Page 160

Page: 160 / 528

Name

Description

UDP Port for discovery and
test messages

Specifies the port used to receive packets from an SLA Monitor server.

Valid value is an integer from 6000 to 65535. The default value is
50011.

Other

Serial Port

Specifies if the port for network traffic is enabled or disabled.

The options are:

•

Enable

•

Disable (default)

Configuring certificates

About this task

When you click on any configuration field, the screen displays the details of that field in the

Parameter Help section.

Procedure

1. Log in to the web interface as an administrator.

2. In the navigation pane, click

Certificates

3. Configure the following areas:

• Certificates

• Online Certificates Status Protocol (OCSP)

• SCEP

• PKCS12

• Web Server

4. Click one of the following:

•

Save

: To save the configuration changes.

•

Reset to Default

: To revert to the default values.

Certificates field descriptions

Name

Description

Certificates

Available Trusted Certificate

Displays the file names of available certificates for authentication.

Table continues…

Phone configuration

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

160

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Search results

Summary of Contents for J100 Series

Reviews:

Avaya J100 Series, Installing And Administering, Page: 160 / 528

Search results

Summary of Contents for J100 Series

Reviews: