manualshive.com logo in svg

Avaya J100 Series, Installing And Administering, Page: 109 / 528

Share
Download
Avaya J100 Series Installing And Administering Download Page 109

Name

Description

Privacy SLAAC Mode

Specifies the preference for Privacy Extensions in SLAAC.

The options are:

•

Disabled, stable address generated from MAC

•

Stable private address (default)

•

Temporary address

SLAAC Addresses

SLAAC (stateless auto configuration) IPv6 addresses.

Value format: eight groups of four hexadecimal digits. The default value
is null.

802.1X Supplicant Operating Mode

Supplicant Operating Mode

Specifies the 802.1X supplicant operating mode.

The options are:

•

Disable (default)

•

Enable (responds only to unicast EAPOL messages)

•

Enable (responds to unicast and multicast EAPOL messages)

802.1x Pass-through
Operating Mode

Specifies the 802.1X pass-through operating mode.

Pass-through refers to the forwarding of EAPOL frames between the
phone's Ethernet line interface and the secondary PC Ethernet
interface.

The options are:

•

Without proxy logoff (default)

•

With proxy logoff

•

Disabled

Authentication Method

Specifies the authentication method to be used by 802.1X.

The options are:

•

MD5 (default)

•

TLS

VLAN

VLAN

Specifies whether the VLAN tagging is enabled or disabled.

The options are:

•

Auto (default)

: To support VLAN functionality by using the phone

network.

•

On

: To support the VLAN functionality by using the internal switch of

the phone.

•

Off

: To disable the VLAN functionality of the phone.

Table continues…

Configuring the phone using the web interface

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

109

Comments on this document? [email protected]

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Reviews:

No comments