Home
/
Avaya
/
J100 Series
/
Installing And Administering

Avaya J100 Series, Installing And Administering, Page: 301 / 528

Share

Page: 301 / 528

Avaya J100 Series Installing And Administering Download Page 301

Parameter name

Default value

Description

AUTO_SELECT_ANY_IDLE_APPR

0

Specifies that any idle call
appearance (primary or
bridged) can be
automatically selected.
This parameter works
along with the parameter
CONF_TRANS_ON_PRIM
ARY_APPR.

Value operation:

• 0: Disabled. Both

parameters
AUTO_SELECT_ANY_I
DLE_APPR and
AUTO_SELECT_ANY_I
DLE_APPR are set to 0.

• 1: Enabled. The

parameter
CONF_TRANS_ON_PRI
MARY_APPR is set to 0.

Note:

Avaya J129 IP Phone
does not support this
feature.

AWAY_TIMER

1

Specifies whether the
phone must report an
away state.

Value operation:

• 0: Disabled.

• 1: Enabled.

AWAY_TIMER_VALUE

30

Specifies the number of
minutes of idle time after
which the phone assumes
that the user is away from
the phone.

Valid values are from 1 to
1500 minutes.

B

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

301

Comments on this document? [email protected]

«
...
299
300
301
302
303
...
»

Summary of Contents for J100 Series

















































































































































































































































































































































































































































































































































Reviews:

No comments